• Highest impact energy electric jack hammer in its class
• Inovative inline design for better balance while breaking
• Heavy wall demolition on masonry and brick
• Removing plaster
• Removing tile on walls and floors
• Making window and door openings
• Uses SDS Max Bits

2700 PSI  Pressure Washer

DCH300x 12" Electric Cut Saw

Can be used with a Vacuum or Wet when hooked to garden hose

Accessory for our LF100 plate tamper - LF100 Information

Can safely run tamper over paver blocks without chipping corners

3500 PSI @ 3.7 GPM Belt Drive Aluminum Frame Pressure Washer, 389cc Honda GX390 OHV With Low Oil Shut Down

K4000 Wet is made for cutting indoors and outdoors. A powerful, versatile electric cutter equipped with a wet cutting kit, to minimize dust and slurry.

**Blade Extra Charge**

The Generac GP3500iO open frame inverter featuring new, advanced PowerRush™ technology delivers over 50 percent more starting capacity for tools and other motor-driven equipment—so you can do more with less.* Both quieter and lighter, it’s the ideal portable solution for camping, powering your RV essentials or tools

12" GAS SAW

**Blade Extra Charge**

• Dual drum drive and articulated steering for accurate control.
• Compact 1-ton roller delivers exceptional compaction performance on asphalt and granular soils.
• Front drum vibration with rear static drum
• Higher exciter frequency for faster compacting speeds
• Weight 2,700 Lb / 3,000LB with Full Water Tank
• Width 35.4"

MANUFACTURE FACT SHEET

3500 psi Hot/Cold water pressure washer.Engines runs off gas and hot water burner runs off diesel. 

Quick connect nozzles - 0°, 15°, 25° and 40° x 50-foot x 3 ⁄8-inch steel wire-braided high pressure hose with quick connects, Professional-grade insulated trigger gun with safety lock-off, Adjustable pressure insulated dual lance.

Mantis Tiller/Cultivator XP provides the reliable power of the mini tiller  in a 16" tine width for greater productivity. The XP utilizes a dual tine bank drive shaft that provides exceptional control and maneuverability at a wide cut.  Tines spin up to 240 rpm, twice the speed of other tillers, with the speed control and shut-off switch right at your finger tips.

• This electric jack hammer works well for concrete up to 4" thick
• medium demolition
• concrete removal
• heavy floor tile removal

Clean hard to reach places by using extended reach wands. Can be used on siding, house eaves, farm equipment, semi-tractor trailers and multi-story buildings.

• All Hydraulic Operation
• Engine: 38HP
• Cutting Depth Below Grade: 12.5"
• Cutting Height Above Grade: 33"
• Head Swing Arc: 47 degrees
• Width: 34"
• Weight: 1750 lbs.

• This electric jack hammer works well for concrete up to 8" Thick.
• Medium-duty demolition of concrete slabs and foundations
• Breaking work on concrete or other materials in basements and on patios in residential applications
• Breaking out channels for laying pipe in plumbing applications
• Removing concrete for rebar connections and utility connections

Hand Held 14" gas saw, 70 CC. Cyclone precleaning air filter system helps protect the motor from dust. Easy to operate with combined choke and gas control feature. Reversable wheels. Wet kit  included. Abor size 1 in / 20mm. 

**Blade Extra Charge**

MODEL MAY VARY

 Portable Generator is compact yet durable and offers premium quality power, ideal for emergency backup power and job sites.

DSH900 16" Gas Hand Held Cut Saw , 90 CC. Cyclone precleaning air filter system helps protect the motor from dust. Easy to operate with combined choke and gas control feature. Abor size 1 in / 20mm. Can use wet or dry.

**Blade Extra Charge**

Till effectively in small spaces with 18" tilling width  The unique swivel handlebar featured on this compact unit means you can walk alongside your tiller rather than in your freshly tilled earth. Counter-rotating tines break up the most difficult soil, clay, or sod. Wheels and tines work independently of each other to allow your tilling travel speed to be adjusted to the soil conditions.
The operator-friendly controls couldn’t be easier: one handle to set the tine drive and one to adjust the wheel drive. Engage the clutch lever, use the variable speed drive to adjust the ground speed, and engage the tines when you are ready to till. If you need to stop for a moment, drop the clutch and the tines and wheels will stop, leaving your engine running and ready to pick up where you left off.

Hydraulic forward and reverse transmission

18" tilling width

Weight: 460 lbs.

More Information

• 18" blade capacity
• Blade is extra price
• Powered by Honda gasoline Engine

FS 400 18" walk behind gas saw is perfect for small concrete or asphalt road repair jobs. It is also a good saw for making trenches for pipe laying, expansion joints, and cutting channels for cable-laying.

• This electric jack hammer works well for concrete up to 12" Thick
• Medium to heavy-duty demolition of concrete slabs and foundations
• Breaking up asphalt in road building, pipe laying and repair work
• Removing concrete for rebar connections and utility connections

• Easy controls to operate track drive and cutter wheel

• Time-tested track design absorbs impact and provides stability
• Center-mounted cutter wheel provides 134º head swing
• Counterbalance valves on each track drive prevent motors from slipping

3 1/2" CORE BIT FOR SDS MAX ROTARY HAMMER DRILLS

Applications

• Through-holes for water piping, ventilation and other utilities
• Great for drilling holes in cement block and brick

Century 90A FC90 Flux Core Wire Feed Welder 

• WELD ANYWHERE: Plug in the Century FC90 flux-cored wire feed welder anywhere 120V input power is available
• Can weld 18 gauge to 1/4" mild steel
• 0.030mm - 0.035mm wire thickness.
• It has a 6 feet welding gun cable assembly length and a 6 feet ground cable length.